You are now subscribed to the ITU-SG16 list
L-Soft list server at Intel Corporation (1.8c)
LISTSERV at MAILBAG.INTEL.COM
Tue Sep 29 09:48:32 EDT 1998
Tue, 29 Sep 1998 06:48:32
Your subscription to the ITU-SG16 list (Mailing list for parties
associated with ITU-T Study Group 16) has been accepted.
Please save this message for future reference, especially if this is the
first time you subscribe to an electronic mailing list. If you ever need
to leave the list, you will find the necessary instructions below.
Perhaps more importantly, saving a copy of this message (and of all
future subscription notices from other mailing lists) in a special mail
folder will give you instant access to the list of mailing lists that you
are subscribed to. This may prove very useful the next time you go on
vacation and need to leave the lists temporarily so as not to fill up
your mailbox while you are away! You should also save the "welcome
messages" from the list owners that you will occasionally receive after
subscribing to a new list.
To send a message to all the people currently subscribed to the list,
just send mail to ITU-SG16 at MAILBAG.INTEL.COM. This is called "sending
mail to the list", because you send mail to a single address and LISTSERV
makes copies for all the people who have subscribed. This address
(ITU-SG16 at MAILBAG.INTEL.COM) is also called the "list address". You must
never try to send any command to that address, as it would be distributed
to all the people who have subscribed. All commands must be sent to the
"LISTSERV address", LISTSERV at MAILBAG.INTEL.COM. It is very important to
understand the difference between the two, but fortunately it is not
complicated. The LISTSERV address is like a FAX number that connects you
to a machine, whereas the list address is like a normal voice line
connecting you to a person. If you make a mistake and dial the FAX number
when you wanted to talk to someone on the phone, you will quickly realize
that you used the wrong number and call again. No harm will have been
done. If on the other hand you accidentally make your FAX call someone's
voice line, the person receiving the call will be inconvenienced,
especially if your FAX then re-dials every 5 minutes. The fact that most
people will eventually connect the FAX machine to the voice line to allow
the FAX to go through and make the calls stop does not mean that you
should continue to send FAXes to the voice number. People would just get
mad at you. It works pretty much the same way with mailing lists, with
the difference that you are calling hundreds or thousands of people at
the same time, and consequently you can expect a lot of people to get
upset if you consistently send commands to the list address.
You may leave the list at any time by sending a "SIGNOFF ITU-SG16"
command to LISTSERV at MAILBAG.INTEL.COM. You can also tell LISTSERV how you
want it to confirm the receipt of messages you send to the list. If you
do not trust the system, send a "SET ITU-SG16 REPRO" command and LISTSERV
will send you a copy of your own messages, so that you can see that the
message was distributed and did not get damaged on the way. After a while
you may find that this is getting annoying, especially if your mail
program does not tell you that the message is from you when it informs
you that new mail has arrived from ITU-SG16. If you send a "SET ITU-SG16
ACK NOREPRO" command, LISTSERV will mail you a short acknowledgement
instead, which will look different in your mailbox directory. With most
mail programs you will know immediately that this is an acknowledgement
you can read later. Finally, you can turn off acknowledgements completely
with "SET ITU-SG16 NOACK NOREPRO".
Following instructions from the list owner, your subscription options
have been set to "REPRO MIME" rather than the usual LISTSERV defaults.
For more information about subscription options, send a "QUERY ITU-SG16"
command to LISTSERV at MAILBAG.INTEL.COM.
Contributions sent to this list are automatically archived. You can get a
list of the available archive files by sending an "INDEX ITU-SG16"
command to LISTSERV at MAILBAG.INTEL.COM. You can then order these files
with a "GET ITU-SG16 LOGxxxx" command, or using LISTSERV's database
search facilities. Send an "INFO DATABASE" command for more information
on the latter.
This list is available in digest form. If you wish to receive the
digested version of the postings, just issue a SET ITU-SG16 DIGEST
command.
More information on LISTSERV commands can be found in the LISTSERV
reference card, which you can retrieve by sending an "INFO REFCARD"
command to LISTSERV at MAILBAG.INTEL.COM.
More information about the sg16-avd
mailing list