Re: [Robustness] Call Clearing related
Orit, In an event of a restart/crash in a Gatekeeper using gatekeeper routed signaling, I would assume that the preferred behavior of the system would be that existing stable calls will not drop. The Gatekeeper as it recovers will learn about the existing calls by its internal data and by sending IRQ's to the endpoints and then restore the Q.931 and H.245 connections. This will reduce the impact of such an event compared to dropping all the calls. If I understand you suggestion correctly it seems to me that this would be moving toward dropping all the calls. Please correct me if I am wrong. Thanks Tzvi Kasten Networking Infrastructures Group Manager Research & Development VCON Ltd. Tel: 09-9590020 ( 972-9-959-0020) Email: zvik@vcon.co.il http://www.vcon.com
-----Original Message----- From: Orit Levin [SMTP:orit@radvision.com] Sent: Thursday, November 04, 1999 6:30 AM To: ITU-SG16@mailbag.cps.intel.com Subject: [Robustness] Call Clearing related
eSafe Protect Gateway (tm) has scanned this mail for viruses, vandals and suspicious attachments and has found it to be CLEAN.
File: ImpGuideV1.zip (54,781 bytes) Encoding: Base64 Result: Archive is clean. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Hello all! I completely agree that after multiplexing of H.323 calls is possible over the same TCP connection, we have to speak (and upgrade the H.323 specification) explicitly using separate terms: Q.931 logical Connection, H.245 logical Connection and the their TCP channel(s) below. Any better names are welcomed. I would vote for H.323v4 to strike out the old text and rewrite the rules using "new" explicit terminology. I understand that part of this rules are going to be based on the new Robustness work. This is why this Robustness work is so urgent and part of it should be done for H.323v4 i.e. for Feb. 00. So... as a part of this Robustness work and using this new terminology, I would like to start from cleaning up "relatively" simple issues. According to current state of the standard, it is not explicitly mandated to clean H.323 Call if its Q.931 TCP connection is reported to be lost from any reason. There are two reasons being claimed against complete closure of the Call in this situation: (a) May be the other side (or the GK) intentionally closed the Q.931 logical Connection and its corresponding TCP channel in order to free up its internal resources, but still wants the H.245 logical Connection and the Call to stay in place. (b) May be it is a real TCP connection failure, but future Robustness Specification will define a way to recover from TCP connection failure without dropping the Call.
As a result, in practice upon TCP connection failure (which may be a part of other side failure) H.323 calls are being hanging up without local resources freeing so essential for H.323 users (and networks)!!!
I think that considering (a) and (b) as a general case is a mistake. I will try to explain myself below:
(a) If we look in Implementers Guide V.1 (see the attachment) text (which has been lost on its way to V.2), the problem was identified long ago. It was recommended to keep the Q.931 logical Connection open. My question is: Do we know about any commercial H.323v1-v3 implementations that intentionally close Q.931 TCP channel but still expect the Call to be maintained? I suggest to find the practical answer and then debate how to keep these implementations happy.
(b) If the case is a real TCP connection failure, the future possible way to recover is adding application (i.e. H.323) layer means (i.e. messages/parameters) and procedures to open an alternate TCP connection between the parties and associate it to the previous Q.931 logical connection. Therefore if one of the parties is of H.323v1-3, there is no way in the future to find a remedy for such a Call.
The bottom line: If one of the parties in H.323 call doesn't support RobustnessV.1 and Q.931 TCP connection failure has been reported from TCP layer, the call shall be cleared and resources freed.
Any comments? Orit Levin RADVision Inc. 575 Corporate Drive Suite 420 Mahwah, NJ 07430 Tel: 1 201 529 4300 (230) Fax: 1 201 529 3516 www.radvision.com orit@radvision.com -----Original Message----- From: Paul E. Jones <paul.jones@TIES.ITU.INT> To: ITU-SG16@MAILBAG.INTEL.COM <ITU-SG16@MAILBAG.INTEL.COM> Date: Tuesday, November 02, 1999 11:44 PM Subject: Re: [Robustness] Re: Call Clearing related
Chris,
A technical question on the second paragraph of your mail: how do endpoints KNOW that they're connected directly rather than through a gatekeeper, in order to decide whether they can (under the current system) drop the call-signalling channel?
First of all... sorry for the delayed response. I am a bit behind :-)
I, too, noticed this funny little sentence in the standard. In theory, the GK would signal that the call is being routed, but that may not necessarily be the case.
I believe it is clear that we must address this issue. I would like to strike the text as I proposed. I also believe it might be wise to add a paragraph to V4 noting that V3 and older terminals may close the call signaling channel, along the lines of your e-mail.
Another issue we have at hand is that of "what is a call signaling channel?" There used to be a one to one mapping between TCP connections and call signaling channels. This is not the case any longer-- one may have multiple calls over the same call signaling channel and one may not even use TCP.
Making this distinction will be important for the robustness work being started, as the "logical" connection (the call signaling channel) and the "physical" connection (the TCP or UDP connection) must be referred to independently. (I'm quite open to new terms for here...). It is important to recognize whether an endpoint has closed the call signaling channel (as we understand it today) or if the physical connection has failed. Since we do not signal that we are going to close the call signaling channel today-- we just close the socket-- it makes this problem more difficult.
Paul << File: ImpGuideV1.zip >>
participants (1)
-
Tzvi Kasten